Find/Replace Problem in 2.50

[Scantech]

Hello Erel,

Add the below codes to the project and input ")" in Find what textbox. Click Find Next and you will see the problem. Before Ver 2.5, I can step in ")" for every next button pressed. Now it will go into spaces before reaching ")".

Make sure there are some spaces before l.Add to test this.

         l.Add("# Ign Key Codes Stored")
         l.Add("# Keys")
         l.Add("A/C RT")
         l.Add("CCL On")
         l.Add("CFCILF")
         l.Add("Coast Clutch Sol 2/3 Timing")
         l.Add("EGR PSI")
         l.Add("EGR Enable Baro")
         l.Add("EGR Vent Solenoid Fault")
         l.Add("EGR MDSD")
         l.Add("EGR Step Motor 1")
         l.Add("EGR Step Motor 2")
         l.Add("EGR Step Motor 3")
         l.Add("EGR Step Motor 4")
         l.Add("EGR Vacuum Solenoid Fault")
         l.Add("EGR Vacuum Solenoid")
         l.Add("EGR Valve Position")
         l.Add("EGR Vent Solenoid")
         l.Add("Fuel Rail Temp B2 Volts")

 

[Erel]

Thank you. It is fixed for the next update.

 

[Vader]

Hello Erel,

Add the below codes to the project and input ")" in Find what textbox. Click Find Next and you will see the problem. Before Ver 2.5, I can step in ")" for every next button pressed. Now it will go into spaces before reaching ")".

Make sure there are some spaces before l.Add to test this.

         l.Add("# Ign Key Codes Stored")
         l.Add("# Keys")
         l.Add("A/C RT")
         l.Add("CCL On")
         l.Add("CFCILF")
         l.Add("Coast Clutch Sol 2/3 Timing")
         l.Add("EGR PSI")
         l.Add("EGR Enable Baro")
         l.Add("EGR Vent Solenoid Fault")
         l.Add("EGR MDSD")
         l.Add("EGR Step Motor 1")
         l.Add("EGR Step Motor 2")
         l.Add("EGR Step Motor 3")
         l.Add("EGR Step Motor 4")
         l.Add("EGR Vacuum Solenoid Fault")
         l.Add("EGR Vacuum Solenoid")
         l.Add("EGR Valve Position")
         l.Add("EGR Vent Solenoid")
         l.Add("Fuel Rail Temp B2 Volts")

Hmmm interesting...

Some of my code looks like this:

Private SENSOR_CAS_MSB                As Int = 0x00       ' 
Private SENSOR_CAS_LSB                As Int = 0x01       ' Value * 12.5 RPM
Private SENSOR_CAS_Ref_MSB            As Int = 0x02       ' 
Private SENSOR_CAS_Ref_LSB            As Int = 0x03       ' Value * 8 RPM
Private SENSOR_MAF_MSB                As Int = 0x04       ' 
Private SENSOR_MAF_LSB                As Int = 0x05       ' Value * 5 mV
Private SENSOR_CoolantTemp            As Int = 0x08       ' Value - 50 Deg C
Private SENSOR_O2_LH                  As Int = 0x09       ' Value * 10 mV
Private SENSOR_O2_RH                  As Int = 0x0a       ' Value * 10 mV
Private SENSOR_Speed                  As Int = 0x0b       ' Value * 2 kph
Private SENSOR_Battery                As Int = 0x0c       ' Value * 80 mV
Private SENSOR_Throttle               As Int = 0x0d       ' Value * 20 mV
Private SENSOR_FuelTemp               As Int = 0x0f       ' Value - 50 Deg C

Not the same, but definitely related...