Width reduced in TableHost

[ciginfo]

Hello
Why when I use "TableHost" an object with 100% of x in a layout exceeds the right edge. I am forced to program in the layout an object with 95% of x for full view when TableHost is used.
thank you

 

[Erel]

Where is this object? Inside the TabHost?

 

[ciginfo]

The object is on a layout made ​​with the designer and called by the TableHost. It is not in the TableHost directly.

 

[Erel]

Can you upload your layout file?

 

[ciginfo]

Here all the program.

 

[Erel]

Where is the relevant code (which line / sub)?

 

[ciginfo]

I don t understand. What is relevant code (which line / sub)

 

[Mahares]

1. I think Erel wants to know which object (Panel?, Label?, Listview?,etc. ) that exceeds the 100%x and where in your code you refer to it? You need to provide more details concerning the problem (un peu plus de details).
2. I, for one could not run your project because it is missing the 4 png files in this below code:

bmp1_enreg = LoadBitmap(File.DirAssets, "enreg_01.png")
bmp2_enreg = LoadBitmap(File.DirAssets, "enreg_02.png")
bmp1_review  = LoadBitmap(File.DirAssets, "review_01.png")
bmp2_review  = LoadBitmap(File.DirAssets, "review_02.png")

3. C'est TABHOST, non pas TABLEHOST.

 

[ciginfo]

OK
All objects (panels, labels, buttons etc ) exceed 100% x.
Every object built with designer and touches the right border of the layout exceeds the layout when it is called with tabhost.

Ok for tabehost

 

[Mahares]

Post missing files please,?,,

 

[barx]

I had the same problem, was some time ago i worked on this particular project though. Think I gave a 20dip padding around, i.e. set the tabhost.left to -20dip and the width to (100%x + 40dip)

 

[ciginfo]

In fact, attached a small program that shows my problem. the first image shows the layout when the designer is connected to the virtual device, the second image shows the layout called by tabhost after program launched.
Designer layout : Widht 480, Height 800, Scale 1.5 (for galaxy S2).

 

[Erel]

Where is the code that set the width? I don't see any designer script.

 

[ciginfo]

There is no code to set the width of the objects. The width of the objects is in the designer (files.bal). It's not the good way?

 

[Erel]

You can only specify percentage units in the designer scripts or code.

 

[ciginfo]

Yes, but when I place with the designer an object against the right edge of the layout, object is not fully seen when the layout is called with the tabhost.
Why? What i have to do?

 

[Informatix]

Yes, but when I place with the designer an object against the right edge of the layout, object is not fully seen when the layout is called with the tabhost.
Why? What i have to do?

Nothing strange here. You can see that your label does not start against the left edge, then how could you expect it to be correctly sized if you set its width to the maximum screen width ? It is obvious that the TabHost has an internal padding. You must take it into account and remove the padding width from the label width.
There's an easy solution if you don't want to do computations: set the label width to -1 (FILL_PARENT).

 

[Erel]

It is actually quite simple. You should add this line to the designer script:

Label2.SetLeftAndRight(0, 100%x)

 

[Informatix]

It is actually quite simple. You should add this line to the designer script:

Label2.SetLeftAndRight(0, 100%x)

I will be surprised if that solves the problem...

 

[Erel]

Here: