The staircase project is used to light up with a sensor when someone passes by using a staircase module and a relay module to turn on the light when someone passes.
Something that worked for more than 40 years broke and I had to find a replacement. I want to show what I did. Background: Solar heating systems (for houses) can either be autonomous, where the water circulation is done by itself - hot water go...
This project is made by using a smoke detector module and a buzzer to detect monoxide gases and prevent suffocation due to it.
it is a simple FTP server for ESP8266: it provides an easy way to list, add, remove and delete files in SPIFFS . - it is based on simpleFTP library for arduino (https://github.com/nailbuster/esp8266FTPServer) - it only allows one ftp...
This system have two parts part no 1 include one Dht11 Temperature/Humidity sensor and Mq5 smoke sensor. part one must be install in server room and connect to one of servers. part no 2 include Seven segment display , Buzzer and two Led for alarm...
I have uploaded a tool I called the Serial Connector Graph. It allows you to send data points from the Arduino that will be plotted on a bar graph or you can also send log text messages that will be shown in a text area. I find it is sometimes...
Althought not finished yet, I've this project at 75% (hope) finished (objectives were learn linux, NodeMCU, use devices on my own and have a safety home) The core system is a Rpi3, which: - Have a cheap USB camera attached (PS2 eyetoy camera) -...
1.8", 128x160 pixels TFT driven by Arduino Uno or Nano to display pictures from SD card. TFT driver is ST7735. The SD is interfaced by the main ATMEGA ISP and the TFT interfaced by USART as ISP. The code reads the SD 54 bytes at a time and...
A sound recorder and playback for Arduino Uno or Nano with ATMEGA328P device using SD card. The card is initialized by the rSD lib and then the code reset the ATMEGA SPI to the code settings. The code uses commands for multi sector reading and...
Hi All, In fact this is not a creation, but an added value for those designing hardware using Arduino and Bluetooth HC-5 or equivalent. This is a ready made board and can be bought for less than a dollar from eBay. A plug-and-play board .. just...
it is a RF 433mhz Repeater with esp8266 hard configuration: - 1 esp8266 Witty Cloud - in front of 433mhz : tested with receptor RXB6 and RX470B. tested with transmitter WL103 /STX882 receptor and transmitter are connected to power 5V and...
Hi everybody, Thanks to B4R I was able to develop a Data Logger and remote console for my main project, a food metal detector. This pjt show whatever is on MD main display and simulate it's four buttons remotelly. It stores on local SD some log...
My first B4R project is finally done. The device monitors air & pool temperature and allows me to toggle the pool's heater (Auto or Standby) as well as set up a 7-day schedule for days when I want the pool heater to run. It's internet-connected...
Plotting a graph on Nextion Touch Screen 7 inch with capacitor charging data...
Low frequency oscilloscope for PC using Arduino Uno or Nano. The input is to pin A0 of the Arduino which connected to PC via USB .Bandwidth up to 5KHz. The sampling is done by the Arduino ADC in a speed of about 36K sampling per sec. The Arduino...
The goal of this Make Project parkSTOP is to build a parkSTOP device (Arduino UNO, B4R) to visually indicate via LED & Sound, if parking position reached. In addition, indicate via Android App (B4A) , connected via Bluetooth, the actual distance...
Oled display of text and bitmap and analog bar. The code uses wire lib only to drive the I2C, the text and bitmap and analog bar are generated by functions in the code. The bitmap code is for size 48x16 for other sizes the code has to be...
OLED 0.95", SSD1331, 96x64 display driven by Arduino Uno or Nano to display pictures from SD card. The SD is interfaced by the main ATMEGA ISP and the Oled interfaced by USART as ISP. The code reads the SD 96 bytes at a time and streams them to...
OLED low frequency oscilloscope, bandwidth is DC to 1000Hz. Max sampling rate is 16000 samples per second. An oscilloscope with these specifications has limited use, but it is a good exercise in using OLED display. rWire lib is used for I2C...
Electronic lock 4 digits code. Digits are stored in the EEPROM. To change code press pushbutton once and enter 4 digits. The relay operates for 2 seconds to unlock. B4R code uses rEEPROM lib and rWIRE lib. The keypad is matrix 3x4, the Oled is...